RSx3-Response H.C

No. 30121
End of production

[Specifications]

<Speed type servo>
#Torque:17.6Kg-cm Speed: 0.06sec/60deg(@7.4V)
#Torque:14.5Kg-cm Speed: 0.07sec/60deg(@6.0V)

#Dimensions: 41x37.5x20mm(Standard size)
#Weight: 69.9g
#Operating voltage:6.0 to 7.4V(Lipo,Life,Ni-MH)
#The hard alumite aluminum gear
#Core-less motor
#Dual ball bearings
#The hard servo gear shaft
#The aluminum top case
#The aluminum heat shink middle case
#Gold plated connector
#Black cable
#HCS Compatible

#Recommend category
  1/8 Off road, 1/8 On road.
 

Madein Japan.


  • (The above banner image is 30122 RSx3 Power H. C.)

     

    Newly designed top case made of Aluminum!

    The aluminum top case support the stable ‘Holding Power’
    The case is machined after anodizing, creating a sharp design and beautiful edge line of the case.
    By shaving off the inside of the case to extremity, while securing sufficient strength, the case is made lighter than the former aluminum case.The black wire servo leads with cool appearance provides suitable softness for installation, while securing necessary current capacity.

     

    HCS Compatible.

    HCS (High speed Communcation System) is the new high speed communication system between the receiver to the servo. The HCS mode shortens communication time of the signal which is compressed. HCS compatible servos is changing mode automatically by signal from receiver. So HCS compatible servos can use with all receivers.  
    If you want to use servos by HCS, please use with HCS compatible receivers.

     

    Installed preset settings

    The following factory MODEL settings are pre-installed. 
    You can chenge setting by Servo model selector.

    Model1: Standard setting(All category)
             2:"Cody King"setting(1/8GP - Off road)
             3:2016Japan national-turf(1/10EP Off-road)
             4:Dirt(1/10EP Off-road)
             5:For Technical Circuit(All category)

    *Model1 has been selected in factory setting.

    Features

    Current servos have the appearance of high speed and high power from the response of 2.4GHz and the power from Li-po batteries respectively. This creates a huge demand upon the servo. The RSx is the racing servo with the durability and operability to employ this high-spec demand.

    1:Case

    The middle case is machined from one piece of aluminum that incorporates the gear pins and motor being held properly in place. The top case rigidity has been improved with the addition of two screws in the middle to prevent flex and keep the gears properly aligned. The upper Hard Case (H.C) is also machined from aluminum. H.C is the distinction of durability for categories that demand high stress.

    2:Motor

    A servo motor is a very important part of a servo. The specification of a servo is up to the motor being used. We have developed a new motor suitable for the new R/C standard with numerous performance and stress tests.

    3:Gear

    The gears are made with a special Japanese aluminum. This gear is 45% lighter than brass and has the same hardness as steel. The ‘Light Weight’ design provides a clean response for driving and reduces the burden on the servo motor. The thorough quality control of the manufactured gears ensures the least amount of backlash possible for smooth action. And Power and Pawer HC use Special Stainless Gear. It is very strong and useful for off load category.

    ICS

     You can change servo's setting when you use our software" ICS Servo Manager".
    Ex, parameter of stretch. More retentivity in High grip condition, less retentivity in Low grip situation,
    You can select value by grip situation for best setting servos.

     

     

    Mode

    The modes you can select on your servo depend on the transmitter and receiver you are using. Please refer to the table below.

     

     

    ---Note---

    The servo is powered on there may be a slight glitch, this is normal (situation).
    We recommend this servo use for steering control.

    Contents

    Servo x1
    Grommet x4
    Screw for Horn x1

  • RSx3-Power H.C

    End of production
    No. 30122

    RSx3-Response

    End of production
    No. 30123

    RSx3-Power

    End of production
    No. 30124

    Carbon Servo Horn 16.5mm

    End of production
    No. 36026

    Carbon Servo Horn 18.5mm

    End of production
    No. 36027

    Carbon Servo Horn 20.0mm

    End of production
    No. 36028

    Servo Model Selector

    End of production
    No. 61029

    ICS USB Adapter HS


    No. 61028
  • Servos

    RSx3 / BSx3 Series Manual

    KO Driver

    KO Driver 2015

    Servo Manager

    ICS ServoManager Software Ver2.0.1.0
    This software can setting for RSx/BRx2/RSxone10/BSx2one10/RSx-12. Also you can use setting data from our.

    Servos

    RSx RSx2 Factory setting data(for ICS Servo Manager2.0)
    This is factory setting data which can use by Servo Manager2.0.

    Dimensions Draw RSx3-Power H.C/Response H.C

    Servo

    Servo Fitting Chart
    Fitting chart for various KO Servo.

    ICS

    About ICS(new version 10.2017)