RSx3-one10 Flection
End of production
[Specifications]
#Torque: 12.5Kg-cm Speed: 0.09sec/60deg(@7.4V)
#Torque: 11.8Kg-cm Speed: 0.10sec/60deg(@6.0V)
#Dimensions: 40.5×26×21mm (Low Profile)
#Weight: 53.3g
#Operating voltage: 6.0~7.4V (Lipo,Life,Ni-MH)
#The hard alumite aluminum gear
#Core-less motor
#Dual ball bearings
#The hard servo gear shaft
#The aluminum top case
#The aluminum heat sink middle case
#Black cable
#Gold plated connector
#HCS Compatible
#Recommend category
1/10 EP on road, 1/10 EP Off road, 1/10 GP On road.
Made in Japan.



-
■A supple and powerful driving feel that touches the road!
Flection means flexible and Curvature, it will touch the road with smooth cornering. With the delicate operation and enhanced torque of the newly developed core-less motor, we have acquired an unprecedented handling performance.
■A completely newly designed, new generation of core-less motor is adopted!
A completely newly designed core-less motor has succeeded in greatly reducing power consumption while pursuing extreme performance at a size that can be mounted on a low profile servo. We have dramatically reduced the probability of adverse phenomena such as weakness of servo due to the ESC BEC circuit current dropping.
■New design aluminum top case
After the primary anodizing, further cutting and a secondary anodizing is applied. The top case is manufactured through a double anodizing process and is finished by becoming very lightweight while securing adequate strength by cutting the inner thickness to the limit. A delicate and fearless design form was born, which imagined the suppleness and strength of Flection.
■Easy handling black servo lead
The black cable that is installed also has the softness that is optimum for handling while securing the necessary current capacity.
■Compatible for H.C.S
HCS (High speed Communcation System) is the new high speed communication system between the receiver to the servo. The HCS mode shortens communication time of the signal which is compressed. HCS compatible servos is changing mode automatically by signal from receiver. So HCS compatible servos can use with all receivers.
If you want to use servos by HCS, please use with HCS compatible receivers.
■Installed preset settings
The following factory MODEL settings are pre-installed.
You can change setting by Servo model selector.MODEL1. EP on-road car. (Selected)
MODEL2. EP on-road car for carpet
MODEL3. EP on-road car for low grip situations.
MODEL4. 1/10 Nitro car Steering.
MODEL5. 1/10 Nitro car Throttle.
*Model 1 is selected in Factory setting.
Inherit the ICS system of RSx / BSx!The RSx / BSx series active worldwide makes common ICS system available. Although the optimum parameters for normal running are set at the time of shipment, it is also possible to further refine each parameter by connecting it to the PC. Please download ICS Servo Manager from here.
*ICS USB adapter HS is required to connect with PC.
Contents
Servo x1
Grommet x4
Screw for Horn x1 -
Servos
RSx3 / BSx3 Series Manual
Servo Manager
ICS ServoManager Software Ver2.0.1.0
This software can setting for RSx/BRx2/RSxone10/BSx2one10/RSx-12. Also you can use setting data from our.Servos
Flection Electric touring car Middle grip outdoor asphalt course Recommended setting
Flection Engine Recommended set of touring car rubber tire specifications
Flection Engine Recommended set of touring car form tire throttle specifications
Flection for Electric Touring car with 17.5t Motor boosted in the High traction
Recommend setting data of Flection for steering in the 1/10 GP Car.
Recommended setting data of Flection for touring stock at AOC
RSx3-one10Flection Factory setthing
RSx3-one10Flection Setting data for EP 2WD Sat surface
Servo
Servo Fitting Chart
Fitting chart for various KO Servo. -
2018 JMRCA 1/10 Electric Touring car Japan National