This is compatible for HCS function of receiver and Servo.
This is a more advantageous set than purchasing for each product.

Channel1 of receiver setthing is HCS mode by factory setting. You can use servo of the product without receiver's setthing.

■Compatible for H.C.S

HCS (High speed Communcation System) is the new high speed communication system between the receiver to the servo. The HCS mode shortens communication time of the signal which is compressed. HCS compatible servos is changing mode automatically by signal from receiver. So HCS compatible servos can use with all receivers.

If you want to use servos by HCS, please use with HCS compatible receivers. 
Please visit our explain for HCS.

RSx3 Power H.C

The aluminum top case support the stable ‘Holding Power’
The case is machined after anodizing, creating a sharp design and beautiful edge line of the case.
By shaving off the inside of the case to extremity, while securing sufficient strength, the case is made lighter than the former aluminum case.The black wire servo leads with cool appearance provides suitable softness for installation, while securing necessary current capacity.

Installed preset settings

The following factory MODEL settings are pre-installed. 
You can chenge setting by Servo model selector.

Model1: Standard setting(All category)
         2："Cody King"setting(1/8GP - Off road)
         3：2016Japan national-turf(1/10EP Off-road)
         4：Dirt(1/10EP Off-road)
         5：For Technical Circuit(All category)

*Model1 has been selected in factory setting.

Features

Current servos have the appearance of high speed and high power from the response of 2.4GHz and the power from Li-po batteries respectively. This creates a huge demand upon the servo. The RSx is the racing servo with the durability and operability to employ this high-spec demand.

1:Case

The middle case is machined from one piece of aluminum that incorporates the gear pins and motor being held properly in place. The top case rigidity has been improved with the addition of two screws in the middle to prevent flex and keep the gears properly aligned. The upper Hard Case (H.C) is also machined from aluminum. H.C is the distinction of durability for categories that demand high stress.

2:Motor

A servo motor is a very important part of a servo. The specification of a servo is up to the motor being used. We have developed a new motor suitable for the new R/C standard with numerous performance and stress tests.

3:Gear

The gears are made with a special Japanese aluminum. This gear is 45% lighter than brass and has the same hardness as steel. The ‘Light Weight’ design provides a clean response for driving and reduces the burden on the servo motor. The thorough quality control of the manufactured gears ensures the least amount of backlash possible for smooth action. And Power and Pawer HC use Special Stainless Gear. It is very strong and useful for off load category.

KR-415FHD

2.4GHz FHSS receiver includes dual receiver circuits​

KR-415FHD achieves a highly precise receiving performance
with the use of a dual circuit and an external and internal antenna. 



 

The pale -type case design

This is 5.5 mm thiner  than previous models.
So, Car gravity is  lower, and you can easy installation to the Radio box on the car

 

New HCS compatible

The HCS mode shortens the communication time of the signal which has been compressed.
KR-415FHD can change a mode to each channel 1-4 indiviually.

HCS is a communication method to largely improve linearity of the servo movement. When using HCS mode, correspondence servos（ex, RSx3/BSx3series）are required. The correspondence servo recognizes both modes automatically.

How to change the mode.​

1,Switch off the receiver and connect the mode selector to a channel that you would like changed.
2,While pushing the set button on the receiver, turn the power source ON. When the LED of the mode selector lights up, the change is completed。

The correspondence servo recognizes both modes automatically. So you do not change mode operation to the servo. 

 

Initial setting of each channel

In this products, Channel 1 and 2 setthing are HCS mode. So you can use servos in the products without receiver setting.

Servo model Selector

The Servo Model Selector is a product that changes the model memory selection of KO PROPO RSx and BSx series servos easily.

#What is memory of servos.

RSx, Bsx series(except Bsx Standard).  Thease servos can memorize settings of each parameter  in a servo.

You can change models of servos.

#About the specification of the main unit

Connect wire of Servo moel selector to Receiver.( or Battery) and connect servo to this Unit. You will know the model number memory by the number of flashes from the LED.
The number of flashes of the LED are changed by pushing the button of the unit.

Current model number is the pattern of flashes of the LED.

#Product usage

Factory setting of each servos  are diffrent. Now(May 2016), No.1 to No.5 memories are same parameter.
But BSx2 one10 Grasper has 2 diffrent model in memories.

Model1 is High spec setting for expert racing. Model2 is more mild setting for drivers. Factory default setthing is model2.
If you use Servo model selector, you can change models of servos easily. 

And you can download some servo setting from our site. Ex RSx12 are 5 setthings in our site.
Please see support tab in on eath products page.

RSx3 Power H.C x2 
KR-415FHD x1